GRACO 24N093 – Husky 515 1/2 in NPT PP Pump, PP Center Section, PP Seats, PTFE Balls & PO Diaphragm

GRACO 24N093 – Husky 515 1/2 in NPT PP Pump, PP Center Section, PP Seats, PTFE Balls & PO Diaphragm

Industrial-grade diaphragm pump component featuring polypropylene construction with PTFE balls for chemical resistance and reliable performance in demanding industrial applications

The Husky 515 air-operated double diaphragm pump features a stall-free low pulsation air valve which provides a smooth and rapid changeover.

The bolt through fluid cover design eliminates leaks and makes the Husky safer with higher reliability.

Center and end porting options.

No mechanical seals to cause fluid leaks or failures

Runs quietly at less than 85 dBa with easy-to-use remote muffler capability for even lower noise levels

Easy-to-service air valve and ball checks

Operates on as little as 20 PSI (1.4 bar, 0.14 MPa)

Split manifold option to pump multiple fluids without mixing

Delivery up to 15 gpm (56.7 lpm)

Reliable air valve for years of dependable performance

Additional Specifications

Material: Polypropylene air motor, fluid section, and seats with PTFE balls

Pump Size: 0.5 in

Air Motor: Poly

Fluid Section: Poly

Seats: Poly

Pump Type: 515

Same As: D5291

Diaphragm Type: overmolded

Air Exhaust Port Size (in)	3/8
Air Exhaust Port Thread Gender	Female
Air Exhaust Port Thread Type	NPT
Air Inlet Size (in)	1/4
Air Inlet Thread Gender	Female
Air Inlet Thread Type	NPT
Application	Industrial
Ball Material	PTFE
Center Section Material	Polypropylene
Compatible Material	Antifreeze, Detergents, Resin, Polymers, Motor Oil, Grease & Oil, Hydraulic Fluid, Transmission Fluid, Cutting Oil, Water – Wastewater Treatment, Ink
Connection Type	Threaded
Diaphragm Material	PTFE Overmold
Fluid Inlet Size (in)	1/2
Fluid Inlet Thread Gender	Female
Fluid Inlet Thread Type	NPT
Fluid Outlet Size (in)	1/2
Fluid Outlet Thread Gender	Female
Fluid Outlet Thread Type	NPT
Fluid Section Material	Polypropylene
Manifold Configuration	Center Port
Manifold O-Ring Material	PTFE
Material	Polypropylene
Maximum Air Consumption (SCFM)	28
Maximum Air Pressure (MPa)	0.7
Maximum Air Pressure (psi)	100
Maximum Cycle Rate (CPM)	400
Maximum Flow Rate (GPM)	15
Maximum Fluid Pressure (MPa)	0.7
Maximum Fluid Pressure (psi)	100
Maximum Operating Temperature (°F)	150
Maximum Solid Size (in)	0.09375
Minimum Operating Temperature (°F)	40
Overall Height (in)	10.63
Power Source	Air
Seat Material	Polypropylene
Standards Met	ATEX, CE
Type	Pneumatic Diaphragm Pump
Weight (lb)	6.5

Features

PTFE/EPDM overmolded diaphragms for chemical compatibility

Polypropylene construction for corrosion resistance

PTFE balls for superior sealing and chemical resistance

NPT threaded connections for easy installation

0.5 inch pump size for moderate flow applications

Applications

Industrial fluid transfer

Chemical processing

Corrosive fluid handling

General industrial pumping applications

Compatible Equipment

Husky industrial pump series

Husky 515

Related Parts

24N094 – Husky 515 1/2″ BSP PP Pump, PP Center Section, PP Seats, PTFE Balls & PO Diaphragm

24N095 – Husky 515 PVDF Pump PP Center Section, PVDF Seats, PTFE Balls & PTFE Overmolded Diaphragm

24N096 – Husky 515 1/2 in NPT AC Pump, PP Center Section, AC Seats, PTFE Balls & PO Diaphragm

24N097 – Husky 515 AC Pump, PP Center Section, SS Seats, SS Balls & PO Diaphragm

24N098 – Husky 515 1/2″ BSP AC Pump, PP Center Section, AC Seats, PTFE Balls & PO Diaphragm

26C020 – HUSKY PUMP,515P-PP01AP3PPPTPOPT

Part of GRACO’s industrial pump series with PTFE/EPDM overmolded diaphragms. Temperature range: 40°F to 180°F (4°C to 82°C). Complies to FDA21CFR 177.1550 (PTFE) and FDA21CFR 177.2600 (EPDM) safety standards. Has overmolded diaphragm parts shown in table below (referenced table not visible on this page). Listed under ‘Pumps with Overmolded Diaphragms’ section.

Reference Manuals

338940 (Page 2) PTFE/EPDM Overmolded Diaphragms

308981 (Page 24) Air-Operated Diaphragm Pumps